Installation, Use and Maintenance - Cda ECH61SS Manual

Installation, Use and Maintenance - Cda ECH61SS Manual

Sponsored Links

User Manual Summary


Search in this Manual:

Installation, Use and Maintenance - Page 1

www.cda.eu ECH Extractors Installation, Use and Maintenance

..

Appliance information: - Page 2

2 Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowledge about it, unless they have had supervision or instructions on how to use the appliance by someone who is res..

CE Declarations of Conformity: - Page 3

3 CE Declarations of Conformity: This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Gas safety, Electrical safety (LVD) and Electromagnetic interference compatibility (EMC). IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposing of a household appliance separately avoids possible negative consequences fo..

Please note: - Page 4

4 Please note: • Under no circumstances should the extractor be connected to any gas ventilation system, flue system or hot air ducting system. • Do not vent the extractor into an attic or loft space. • Only house the extractor in rooms with adequate ventilation. Remember that the extractor is powerful and whatever air is extracted needs to be replaced. • Do not tile the extractor in. It should be removable for service or maintenance. • Do not use silicone sealant to secure the hood to the wall. • You must be able to isolate the extractor from the mains electrical supply after ..

Using Your Extractor - Page 5

5 Fig. 1 Using Your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. Control Panel A – Power indicator light B – Light button C – Power off button D – Speed level buttons To switch the extractor light on or off • Press button “B”. To switch on the extractor or to change the speed at any time when the extractor is running • Press the relevant button “D” for the first, second or third speed level as required. To switch the extractor off • Pr..

Care and Maintenance - Page 6

6 Care and Maintenance IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean your extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Cleaning the grease filter The grease filter should be kept clean to minimise the risk of fire. At least once a month you should remove and clean the gr..

To remove the grease filter - Page 7

7 To remove the grease filter To remove the grease filter, push in the button on the handle and then pull down on the filter at the front as shown in figure 2. When you have released it at the front, then you can pull the filter out completely. Please note: Cleaning the grease filter in the dishwasher may lead to discolouration. This is normal and does not constitute a fault with the appliance. Changing the charcoal filter (re-circulating only) To ensure best performance of your extractor, you should replace the charcoal filters every four to six months, depending on use. To attach ..

Changing a Light Bulb - Page 8

8 Changing a Light Bulb DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOV- ING IT. Remove the grease filter, unscrew the light bulb and replace the light with the required light bulb as shown below. Finally, replace the grease filter. The ECH extractors are designed for 50W maximum halogen 2 pin GU10 bulbs. Do not touch bulbs or adjacent areas during or straight after pro- longed use of the lights. The light is designed for use during cooking and not for general room illumination. Extended use of the light can reduce the life span of..

Mains Electricity Connection - Page 9

9 DOUBLE POLE SWITCHED FUSED SPUR OUTLET USE A 3 AMP FUSE Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations. The wires in the mains lead of this appliance are coloured in accordance with the following code: BLUE = NEUTRAL, BROWN = LIVE. As the colours of the wires in the mains lead..

IMPORTANT: THIS APPLIANCE IS A CLASS II APPLIANCE - Page 10

10 • If the mains cable is damaged, it must be replaced by a CDA approved engineer, agent or similarly qualified person in order to avoid a hazard. NOTE: USE A 3A FUSE Assembly and electrical connection should be carried out by competent personnel. When installing this product we recommend you seek the help of another individual. IMPORTANT: THIS APPLIANCE IS A CLASS II APPLIANCE (DOUBLE INSULATED) AND IS NOT INTENDED TO BE EARTHED. DO NOT FIT AN EARTH LEAD TO THIS EXTRACTOR. Do not mount the isolation switch behind the chimney section. It is a requirement that you must be able to isolate..

Electrical Information - Page 11

11 Electrical Information Mains electrical voltage: 230 – 240Vac Total rated power consumption: 240W Troubleshooting Please note: Your extractor is equipped with a motor protection device that will switch off the motor to prevent damage from overheating. This may happen during cooking when most or all of the zones/burners are being used simultaneously, or if your extractor is installed incorrectly, lower than the recommended height. This is normal, and the extractor will work again once the motor has cooled sufficiently. If your extractor is not working 1. Check that the mains supply has..

Mounting Your Extractor - Page 12

12 Mounting Your Extractor When the extractor is to be installed above an electric hob, the minimum distance between the hob and extractor must exceed 600mm (650mm is recommended). When the extractor is to be installed above a gas hob, the minimum distance between the hob and extractor must exceed 700mm (750mm is recommended). If the instructions provided with your gas hob state that the required distance between the hob and extractor must be greater than 700mm, then that is the distance that should be observed; this is a legal requirement and may lead to your hob being disconnected from th..

13 - Page 13

13 IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE GAS HOB, THE MINIMUM DISTANCE BETWEEN THE HOB AND EXTRACTOR MUST BE AT LEAST 760mm. The width of any hob must not be greater than the width of the extractor installed above it.

..

Installation - Page 14

14 Installation Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Tools required Mark wall as required (see table on page 12) Drill holes Fit wall fixings and top screws - Ensure that any fixings you use are appropriate for the wall type. Secure hood (tighten all screws)

..

IMPORTANT SAFETY WARNING: - Page 15

15 Fig. 11 Fit ducting adaptor IMPORTANT SAFETY WARNING: ONLY USE THE SCREWS PROVIDED WITH THE EXTRACTOR TO MOUNT THE DUCTING ADAPTOR. THE USE OF LONGER SCREWS MAY CAUSE DAMAGE TO THE INTERNAL WIRING WHICH WILL NOT BE COVERED BY THE GUARANTEE. Fig. 13 Mount chimney brackets Fix ducting (seal joint) Fig. 12

..

Ducting and Ventilation - Page 16

16 Fig. 14 Fig. 15 Mount the chimney Adjust and secure the chimney Ducting and Ventilation For best performance and lowest noise output, we recommend the use of 125mm ducting. 100mm ducting may be used but this will reduce performance and increase the noise of the extractor. Installation for Recirculation When installing this extractor for re-circulating the air within your room we advise use of the optional carbon filters to help remove odours.

..

NOTES: - Page 17

17 NOTES:

..

NOTES: - Page 18

18 NOTES:

..

Energy Efficiency Information - Page 19

19 E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the right to change specifications without prior notice. Energy Efficiency Information Attribute Symbol Value Units Model identification ECHxx Annual Energy Consumption AEC Hood 135.4 kWh Time increase factor f 1.7 Fluid Dynamic Efficiency FDE Hood 9.3 (E) Energy Efficiency Index EEI Hood 106.9 (E) Measured airflow at Best Efficiency Point Q BEP 227.7 m 3 /h Measured pressure at Best Efficiency Point P BEP 150.0 Pa Maximum airflow Q MAX 427.4 m 3 /h Measured electric power at Best ..

Customer Care Department - Page 20

www.cda.eu Please contact our Customer Care Department for Service on the details below Customer Care Department The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] Copyright © CDA 2015

..
www.cda.eu
ECH
Extractors
Installation, Use and Maintenance